PRODUCTS
Silicones & Sealants
Adhesives & Glues
PU Foams
Spray
Hotmelt
HOW TO USE
Wear gloves to avoid skin contact, Remove dust and dirt from the surface. Dampening the surfaces to be bonded can increase the rate of cure, Ensure good contact between the joint surfaces before application, Apply the adhesive to one surface to be bonded as a thin layer, apply press for 15 - 20 minutes.
For Safety: May cause an allergic skin reaction. May cause allergy or asthma symptoms or breathing difficulties if inhaled. Keep out of reach of children. Do not handle until all safety precautions have been read and understood. Avoid breathing fume, gas, mist, vapours. Wear protective gloves, protective clothing, eye protection, face protection. In case of inadequate ventilation, wear respiratory protection.
Cleaning the surfaces with a solvent will definetely improve the adhesion
The application temperature must be between +5°C and +40°C.
After the application, the sealant must be tooled with light pressure within 5 minutes to spread the material against the joint surfaces and to obtain a professional finish.
For Safety: Keep out of reach of children. Do not get in eyes, on skin,
or on clothing.
Do not use at temperatures below +5°C., The elements to be bonded must be properly clean and free from dust and grease, One of the substrates must be porous to ensure better curing, Apply the adhesive with a brush as thin film to one or both surfaces and join the parts within 10 minutes, Press the elements together for approximately 15-20 minutes, Uncured adhesive can be cleaned by acetone.
For Safety: May cause an allergic skin reaction, May cause allergy or asthma symptoms or breathing difficulties if inhaled, Avoid breathing dust/fume/gas/mist/vapours/spray, Wear protective gloves. protective clothing, eye protection, face protection. IF ON SKIN; Wash with plenty of water and soap.
The recommended joint depth/width ratio is 1 to 1 Application temp. is between +5°C and +40°C. Mediately after the application, smooth the sealant at once with wet finger or a wet tool
Keep the sealed joint dry at least for two hours.
For Safety: Keep out of reach of children. Do not get in eyes, on skin, or on clothing.
Shake the product well before use.Screw the adapter on the valve.
Hold the can upside down and activate the foam by pressing the valve.
Moisturizing the surfaces and the foam improves adhesion and shortens curing time.Fresh foam can be cleaned by Foam Cleaner.
Cured foam can be cleaned barely mechanically.
Important Warnings For Safety:
Keep out of reach of children, May cause allergy or asthma symptoms or breathing difficultes if inhaled.Keep away from heat, hot surfaces, sparks, open fiames and other ignition sources.
Substrates need to be smooth and have a perfect connection area, Apply a drop on one of the substrates, Join substrates and press firmly for one minute, Application temperature is between +5°C and +35°C.
For Safety: Causes skin irritation, Causes serious eye irritation, May cause respiratory irritation, Cyanoacrylate, Danger, Bonds skin and eyes in seconds, Keep out of reach of children, Avoid breathing dust, fume, gas, mist, vapours, spray while using Store in a well ventilated place, Keep container tightly closed, Dispose of contents, container through a waste management company authorized by the local government.
Body construction of cars, containers, caravans etc. Sealing and bonding of ventilation ducts, gutters and spouts etc. Sealing of sheet metal seams. For vibration reduction in all type of sheet metal assembly works. Sealing against water, air, gas and dust.
For Safety: May cause an allergic skin reaction. May cause allergy or asthma symptoms or breathing difficulties if inhaled. Keep out of reach of children. Do not handle until all safety precautions have been read and understood. Avoid breathing fume/gas/mist/vapours. Wear protective gloves/protective clothing/eye protection/face protection. In case of inadequate ventilation, wear respiratory protection.
Make sure all connections are clean and free of dirt, dust, oil, grease, water, ice, or old silicone, The applied silicone should be leveled within 15 minutes before it dries.
For Safety: S1/2 Keep locked up and out of the reach of children.
S24 Avoid contact with skin, S51 Use only in well-ventilated areas.
NEW PRODUCT
AQUA FLOOR
Hybrid Waterproofing Membrane
AQUA FLOOR is a premium, liquid and cold applied, one-component silane modified polymer (SMP) based polymer, elastic, waterproofing membrane, free of bitumen, solvent and isocyanates. After fully cured, it forms waterproof, UV resistant surface which also repairs the cracks up to 5mm.
HQ
GIOFIX products are of high performance and achieve the intended objectives in a short period of time, and this is proven through experiments in laboratories and the testimony of our customers.
ECO
All GIOFIX products depend on its policy to focus on preserving the environment through the correct formulations and method of use that reduce environmental damage.
DIY
GIOFIX products are easy to use by following the instructions written on the packages, thus achieving the best results during the correct appliying and saving money.
WHY GIOFIX ?
We see our customers as partners rather than buyers, combining our business acumen with entrepreneurial vision, incredible technical expertise and the ability to execute quickly and efficiently, quickly bringing your idea to market.
As one of the original companies, we have never lost sight of the fact that technological and industrial collaborations and consultations are an essential pillar in scientific development and research.
Simply put, we are personal and practical we rejoice in every success we achieve together with our clients. also finding the unseen edge With creativity, hard work and vision to help clients discover what’s on the horizon.
Contact Us
+90 212 603 77 63
+90 507 777 77 63
info@giofix.com
export@giofix.com
Address
Kavaklı Mah. Oğuzhan
Cad. No: 24 Kat: 4
D. 25 Beylikdüzü /
Istanbul – Türkiye
Follow Us
Copyright GIOFIX ©2023 / All Rights Reserved.